Sale!
W1209 Digital Temperature Controller Thermostat Module
Original price was: ₹120.00.₹87.00Current price is: ₹87.00.
W1209 Module Specifications:
- Input Power (DC): 12V
- Measuring Inputs: NTC (10K 0.5%)
- Waterproof Sensor: 0.5M
- Output: 1 Channel Relay Output,
- Capacity: 10A
- Temperature Control Range: -50 ~ +110 C
- Resolution at -9.9 to 99.9: 0.1 C
- Resolution at all other temperatures: 1 C
- Measurement Accuracy: 0.1 C
- Control Accuracy: 0.1 C
- Refresh Rate: 0.5 Seconds
9 in stock
- W1209 thermostat module has a temperature sensor, keys, LED display, relay and requires DC 12V power supply. It is an affordable, good quality thermostat controller.
- Thermostats are devices that sense the temperature of a system so that the temperature is maintained at the desired set point or near to it. NTC temperature sensor allows the module to intelligently control varied electrical devices based on the temperature.
- NTC thermistor has a negative temperature coefficient, which means the resistance decreases with increasing temperature. W1209 has an inbuilt embedded micro-controller, thus not much programming knowledge is required.
- The module consists of three switches to configure the various parameters including ON and OFF trigger temperatures. The relay can operate at voltages up to a maximum of 240V AC at 5A or 14V DC at 10A to power on.
- The temperature is displayed in degree centigrade and with the help of 7-segment display and the relay, the state is displayed with the help of the LED present on the W1209 module.
Related products
-
2 Channel 5V Relay Module with Optocoupler
Original price was: ₹80.00.₹62.00Current price is: ₹62.00.Add to cartSpecification:
- High current relay, AC250V 10A, DC5V 10A
- 2 LEDs to indicate when relays are on
- Works with logic level signals from 3.3V or 5V devices
- Opto isolation circuitry
* Product Images are shown for illustrative purposes only and may differ from actual product.
-
1 Channel 5V Relay Module
Original price was: ₹55.00.₹33.00Current price is: ₹33.00.Add to cartFeatures :
- 1 channel relay board
- Operating Voltage 5V
- Pull-down circuit for avoidance of malfunction
- Power supply indicator lamp
- Control indicator lamp
- Indicator for Relay output status
- Max Current : 20mA
- Relay Contact Current Capacity at AC250V: 10A
- Relay Contact Current Capacity at DC5V: 10A
- One normally closed contact and one normally open contact
- Triode drive, increasing relay coil
- High impedance controller pin
- Can Be controlled various appliances & other Equipment With Large current.
- Standard TTL Level logic controlled (AVR, Arduino, 8051, PIC, ARM)
- The module is compliant with international safety standards, control and load areas isolation trenches;
* Product Image is shown for illustrative purposes only and may differ from actual product.
-
NODEMCU – ESP8266 Wifi Development Board
Original price was: ₹200.00.₹150.00Current price is: ₹150.00.Read moreNodeMCU is a IoT Module based on ESP8266 wifi Module. NodeMCU uses Lua Scripting language and is an open source Internet of Things (IoT) platform. This modules has CH340g USB to TTL IC.
Features of Node-MCU IoT Module:
- Open source IoT Platform
- Easily Programmable
- Low cost & Simple to Implement
- WI-FI enabled
Specification of Node-MCU IoT Module:
- It is based on ESP8266, integrates GPIO, PWM, IIC, 1-Wire and ADC all in one board.
- Power your development in the fastest way combining with NodeMCU Firmware!
- USB-TTL included, plug&play
- 10 GPIO, every GPIO can be PWM, I2C, 1-wire
-
4 Channel 5V Relay Module with Optocoupler
Original price was: ₹250.00.₹118.00Current price is: ₹118.00.Add to cartFeatures:
- Channel: 4 channel
- Relay Operating Voltage: 3.3V to 5V
- High impedance controller pin
- DC or AC signal, control, you can control the 220V AC load.
- There is a normally open and one normally close contact.
- Triode drive, increasing relay coil
- Pull-down circuit for avoidance of malfunction
- Power supply indicator and Control indicator lamp
- Power supply and relay instructions, lit, disconnect is off.
- Input signal, signal, common Terminal and start conducting.
- Useful for appliance control.
- One normally closed contact and one normally open contact
- The module is compliant with international safety standards, control and load areas isolation trenches.
* Product Image is shown for illustrative purposes only and may differ from actual product.
Reviews
There are no reviews yet.