Digital Sensor TTP223B Module Capacitive Touch Switch
Original price was: ₹78.00.₹20.00Current price is: ₹20.00.
- Power supply voltage(VCC): 2.0, 3, 5.5 V.
- Output high VOH: 0.8 Vcc
- Output low VOL: 0.3 Vcc
- Response time (touch mode) : 60 mS
- Response time (low power mode) : 220 mS
- Can replace the traditional touch of a button
- Four M2 screws positioning holes for easy installation
In stock
TTP223B Capacitive Touch Key Sensor Module is based on a touch-sensing IC capacitive touch switch module. It allows you to remove the worry of conventional push-type keys.
Digital Capacitive Touch Switch Module is based on TTP223B. Normally, it outputs low and keeps at a low power state. When a touch is sensed on the circular marked region, it outputs high and switches to the quick response state. When not being touched for 12 seconds, it switches to a low power state again.
In addition to the thin paper ( non-metallic ) covering the surface of the module, as long as the correct location of the touch, you can make it hidden in the walls, desktops, and other parts of buttons.
Touch Sensor Interface :
- Touch area: Similar to a fingerprint icon inside the area, you can touch the trigger finger.
- Control Interface: A total of three pins (GND, VCC, SIG), GND to the ground, VCC is the power supply, SIG digital signal output pin
- Positioning holes: 4 M2 screws positioning hole diameter is 2.2mm, the positioning of the module is easy to install, to achieve the inter-module combination.
- Power Indicator: Green LED, power on the right that is shiny
Package Includes :
1 x TTP223B Capacitive Touch Key Sensor Module
| Weight | 85 g |
|---|
Related products
-
LDR Module 4 Pin | Digital & Analog Light Sensor for Arduino
Original price was: ₹60.00.₹39.00Current price is: ₹39.00.Read moreFeatures: LDR Module LM393 4 Pin
✅ 4-Pin Output: Provides both digital (D0) and analog (A0) outputs for flexibility in projects.
✅ LM393 Comparator: Fast, reliable switching for accurate light detection.
✅ Adjustable Sensitivity: Onboard potentiometer lets you set the light threshold easily.
✅ Wide Voltage Range: Operates on 3.3V–5V, compatible with Arduino, ESP32, Raspberry Pi, and microcontrollers.
✅ High Stability: Stable performance with precise light sensing in varying conditions.
✅ Indicator LED: Shows digital output state for quick testing and debugging.
✅ Compact Design: Easy to integrate into DIY and IoT projects. -
1 Channel 5V Relay Module
Original price was: ₹55.00.₹33.00Current price is: ₹33.00.Add to cartFeatures :
- 1 channel relay board
- Operating Voltage 5V
- Pull-down circuit for avoidance of malfunction
- Power supply indicator lamp
- Control indicator lamp
- Indicator for Relay output status
- Max Current : 20mA
- Relay Contact Current Capacity at AC250V: 10A
- Relay Contact Current Capacity at DC5V: 10A
- One normally closed contact and one normally open contact
- Triode drive, increasing relay coil
- High impedance controller pin
- Can Be controlled various appliances & other Equipment With Large current.
- Standard TTL Level logic controlled (AVR, Arduino, 8051, PIC, ARM)
- The module is compliant with international safety standards, control and load areas isolation trenches;
* Product Image is shown for illustrative purposes only and may differ from actual product.
-
NODEMCU – ESP8266 Wifi Development Board
Original price was: ₹200.00.₹150.00Current price is: ₹150.00.Read moreNodeMCU is a IoT Module based on ESP8266 wifi Module. NodeMCU uses Lua Scripting language and is an open source Internet of Things (IoT) platform. This modules has CH340g USB to TTL IC.
Features of Node-MCU IoT Module:
- Open source IoT Platform
- Easily Programmable
- Low cost & Simple to Implement
- WI-FI enabled
Specification of Node-MCU IoT Module:
- It is based on ESP8266, integrates GPIO, PWM, IIC, 1-Wire and ADC all in one board.
- Power your development in the fastest way combining with NodeMCU Firmware!
- USB-TTL included, plug&play
- 10 GPIO, every GPIO can be PWM, I2C, 1-wire
-
Arduino Opta WiFi AFX00002 – Industrial IoT PLC | Arduino Pro
Original price was: ₹20,600.00.₹19,800.00Current price is: ₹19,800.00.Add to cartKey Features:
- Powerful MCU: STM32H747XI dual‑core Cortex‑M7 (480 MHz) + M4 (240 MHz)
- Versatile connectivity: 10/100 Ethernet, USB‑C, Wi‑Fi (802.11 b/g/n up to 65 Mbps), Bluetooth Low Energy, RS‑485 serial.
- I/O and switching: 8 configurable digital/analog inputs (0–10 V), and 4 relay outputs (10 A, 250 VAC).
- Secure and future‑proof: Onboard ATECC608B secure element, X.509 compliance, OTA firmware updates.
- Programming flexibility: Supports Arduino IDE sketches and IEC 61131‑3 languages (Ladder, FBD, ST, SFC, IL) via Arduino PLC IDE.
- Industrial-grade ruggedness: DIN-rail mount, IP20 rating, wide operating temperature (−20 °C to +50 °C), multiple certifications (CE, ENEC, UL)
