DHT11 Temperature And Humidity Sensor Module with LED
Original price was: ₹125.00.₹55.00Current price is: ₹55.00.
Features:
- Input Supply voltage (VDC): 3.3 ~ 5
- Supply Current (mA): measurement 0.3mA standby 60μA.
- Temperature measurement range: 0~50 degrees
- Temperature measurement error: ±2 degrees
- Humidity measurement range: 20%~95%RH
- Humidity measurement error: ±5%RH
Only 2 left in stock
The DHT11 Temperature And Humidity Sensor Module with LED is a small humidity and temperature sensor that you can connect to your Arduino and get readings for temperature and humidity in the environment.
Features:
- DHT11 sensor with PCB and LED indicator along with cable; 3 to 5V power and I/O, 4 pins with 0.1″ spacing
- The board has pre-built 4.7K or 10K resistor, which you will need to use as a pull-up from the data pin to VCC.
- 2.5mA max current use during conversion (while requesting data)
- Good for 20-80% humidity readings with 5% accuracy
- Good for 0-50°C temperature readings ±2°C accuracy.
Applications:
- Weather monitoring stations
- IoT and smart home devices
- Greenhouse & agricultural monitoring
- HVAC control systems
- Data logging projects
- Educational electronics projects
Package Includes:
- 1 x DHT11 Temperature And Humidity Sensor Module.
- 3 x Female to Female Connecting cable.
| Weight | 10 g |
|---|
Related products
-
Arduino Nicla Sense ME ABX00050 – Tiny IoT Sensor Hub
Original price was: ₹5,530.00.₹5,100.00Current price is: ₹5,100.00.Read moreKey Features
✅ Bosch BHI260AP: Smart 6-axis IMU with embedded AI for motion detection & gesture recognition.
✅ Bosch BMM150: 3-axis magnetometer for accurate heading and orientation.
✅ Bosch BMP390: High-resolution pressure sensor for accurate altitude detection.
✅ Bosch BME688: Environmental sensor for gas, humidity, temperature, and barometric pressure.
✅ Powerful MCU: nRF52832 (ARM Cortex-M4 @ 64 MHz, BLE 5.0) with 512 KB Flash, 64 KB RAM.
✅ Edge AI Ready: Run TinyML models for real-time analysis on-device.
✅ Tiny footprint: 22.86 x 22.86 mm (0.9 x 0.9 inches).
✅ Compatible: Works standalone or with Portenta/Arduino MKR boards.
✅ Ultra-low power consumption: Suitable for battery-powered IoT edge nodes. -
Digital LDR Module – Light Sensor
Original price was: ₹50.00.₹35.00Current price is: ₹35.00.Read moreFeatures:
✅ Simple to use, plug-and-play.
✅ Adjustable sensitivity using potentiometer.
✅ Low power consumption.
✅ Fast switching compared to analog readings.
✅ Useful in light detection, automatic street lights, daylight sensing, and DIY projects.Applications:
🔹 Automatic night lamp.
🔹 Smart curtains that close when light is high.
🔹 Light intensity alarms.
🔹 Robotics line-following sensors (combined with reflective surfaces).
🔹 Security systems to detect sudden darkness (hand covering sensor). -
SX1278 LoRa Module Ra-02 433MHz Wireless Transceiver
Original price was: ₹799.00.₹367.00Current price is: ₹367.00.Add to cartFeatures:
- LoRa ™ Spread Spectrum modulation technology
- Constant RF power output at + 20dBm-100mW voltage change
- Half-duplex SPI communication
- Supports FSK, GFSK, MSK, GMSK, LoRa ™ and OOK modulation modes
- Automatic RF signal detection, CAD mode and very high speed AFC
- Packet engine with CRC up to 256 bytes
- Small footprint dual-row stamp-hole patch package
- Shielded housing
- Patch Antenna
