BMP180 Digital Barometric Pressure Sensor Module
Original price was: ₹180.00.₹36.00Current price is: ₹36.00.
Features
- Measures barometric pressure, altitude & temperature
- High precision: ±1 hPa (pressure), ±0.5°C (temperature)
- Pressure range: 300–1100 hPa
- Operating voltage: 1.8V–3.6V (3.3V typical)
- I²C interface for easy integration
- Low power consumption (<1 μA in standby)
- Compact & lightweight (~2 g)
- Compatible with Arduino, Raspberry Pi & other microcontrollers
In stock
BMP180 Digital Barometric Pressure Sensor Module is used for measuring barometric pressure and altitude. It also has a temperature sensor for temperature compensation of pressure measurements. It uses push sensors for the BMP180. It offers a pressure measuring range of 300 to 1100 hPa with a relative pressure error of 0.12 hPa.
BMP 180 is a barometric pressure sensor with an I2C interface. Barometric pressure sensors measure the absolute pressure of the air around them. This pressure varies with both the weather and altitude. Depending on how you interpret the data, you can monitor changes in the weather, measure altitude, or any other tasks that require an accurate pressure reading.
Note: (1 hPa ≡ 100 Pa) which is equal to 0.001 bar (atmospheric)
Features :
- I2C interface.
- Max I2C Speed: 3.4Mhz
- Pressure conversion time: 5msec
- Fully calibrated.
- Small and easy to use.
- Voltage supply: 1.8 ~ 3.6 V
- Current supply: 5µA at 1Hz
- Peak current: 1000µA
- Very low noise: up to 0.02hPa (17cm)
- Pressure Range: 300hPa to 1100hPa (+9000m to -500m)
Package Includes :
- 1 x BMP180 Digital Barometric Pressure Sensor Module
- 1 x 4Burg Connector(Straight)
| Input Voltage | 1.8 ~ 3.6 V |
| Interface Type | I2C |
| Max I2C Speed | 3.4Mhz |
| PCB Size ( L x W ) | 1.3 x 1.2 cm |
| Peak Current | 1000µA |
| Pressure conversion time | 5 ms |
| Pressure Range | 300hPa to 1100hPa |
| Weight | 5 g |
|---|
Related products
-
4 Channel 5V Relay Module with Optocoupler
Original price was: ₹250.00.₹118.00Current price is: ₹118.00.Add to cartFeatures:
- Channel: 4 channel
- Relay Operating Voltage: 3.3V to 5V
- High impedance controller pin
- DC or AC signal, control, you can control the 220V AC load.
- There is a normally open and one normally close contact.
- Triode drive, increasing relay coil
- Pull-down circuit for avoidance of malfunction
- Power supply indicator and Control indicator lamp
- Power supply and relay instructions, lit, disconnect is off.
- Input signal, signal, common Terminal and start conducting.
- Useful for appliance control.
- One normally closed contact and one normally open contact
- The module is compliant with international safety standards, control and load areas isolation trenches.
* Product Image is shown for illustrative purposes only and may differ from actual product.
-
Arduino Portenta Breakout Board ASX00031
Original price was: ₹5,170.00.₹4,100.00Current price is: ₹4,100.00.Read moreFeatures
- Power ON Button
- Boot mode DIP switch
- Connectors
– USBA
– RJ45 up to 1Gb/s
– Micro SD card
– MIPI 20T JTAG with trace capability - Power
– CR2032 RTC Lithium Battery backup
– External power terminal block - I/O
– Break out all Portenta High Density connector signals
– Male/female HD connectors allow interposing breakout between Portenta and shield to debug signals - Compatibility
– Standard Portenta High Density connector pinout - Safety information
– Class A
