Dual Axis XY Joystick Module
Original price was: ₹99.00.₹49.00Current price is: ₹49.00.
Joystick Module Features and Specifications:
- Compatible with Arduino or with most of the microcontrollers
- Two independent Potentiometers – one for each axis ( X and Y)
- Auto return to center position
- Low weight
- Cup-type Knob
- Operating Voltage: 5V
- Internal Potentiometer value: 10k
- 2.54mm pin interface leads
- Dimensions: 1.57 in x 1.02 in x 1.26 in (4.0 cm x 2.6 cm x 3.2 cm)
- Operating temperature: 0 to 70 °C
In stock
This is a Dual Axis Joystick Module to measure position coordinates on the X and Y axis by moving the “hat”. Directional movements are controlled by simply two potentiometers of 10k ohm – one for each axis. This joystick also has a select button that is actuated when the joystick is press down.
Features:
- Dual-axis (X & Y) analog joystick for directional control.
- Push button switch included for extra functionality.
- Compatible with Arduino, ESP32, Raspberry Pi, and microcontrollers.
- Standard 2.54mm pins for easy breadboard and jumper wire use.
- Spring return mechanism for smooth centering.
- Compact and durable design for DIY and robotics projects.
Applications:
- Robotics control (robot car, robotic arm, drone gimbals).
- DIY game controllers and simulation setups.
- Arduino and Raspberry Pi projects for motion input.
- RC vehicle remote controls.
- Automation systems requiring manual analog input.
- Mechatronics learning projects.
| Weight | 10 g |
|---|
Related products
-
BLDC 30A ESC – Brushless DC Motor Electronic Speed Controller
Original price was: ₹550.00.₹350.00Current price is: ₹350.00.Add to cartBLDC 30A ESC – Key Specifications
-
Maximum Current: 30A for stable and BLDC Motor Controller
-
Peak Current: 40A (<10 sec) for high-performance bursts
-
BEC Output: 5V/2A to power receivers and electronics efficiently
-
Auto Cut-Off: 2.9V/cell for battery safety and protection
-
Compact Dimensions: 45 × 24 × 9 mm, lightweight 23 g design
-
Optimized for: Drones, RC cars, boats, and robotics applications
-
-
W1209 Digital Temperature Controller Thermostat Module
Original price was: ₹120.00.₹80.00Current price is: ₹80.00.Add to cartW1209 Temperature Controller Module – Specifications
-
Type: Digital temperature controller / digital temp controller
-
Input Power: 12V DC
-
Measuring Input: NTC 10K 0.5% sensor
-
Waterproof Sensor: 0.5M probe
-
Output: 1-channel relay, 10A capacity
-
Temperature Range: -50°C to +110°C
-
Resolution: 0.1°C (-9.9 to 99.9°C), 1°C for other ranges
-
Measurement Accuracy: ±0.1°C
-
Control Accuracy: ±0.1°C
-
Refresh Rate: 0.5 seconds
-
-
1 Channel 5V Relay Module
Original price was: ₹55.00.₹33.00Current price is: ₹33.00.Add to cartFeatures :
- 1 channel relay board
- Operating Voltage 5V
- Pull-down circuit for avoidance of malfunction
- Power supply indicator lamp
- Control indicator lamp
- Indicator for Relay output status
- Max Current : 20mA
- Relay Contact Current Capacity at AC250V: 10A
- Relay Contact Current Capacity at DC5V: 10A
- One normally closed contact and one normally open contact
- Triode drive, increasing relay coil
- High impedance controller pin
- Can Be controlled various appliances & other Equipment With Large current.
- Standard TTL Level logic controlled (AVR, Arduino, 8051, PIC, ARM)
- The module is compliant with international safety standards, control and load areas isolation trenches;
* Product Image is shown for illustrative purposes only and may differ from actual product.
-
NODEMCU – ESP8266 Wifi Development Board
Original price was: ₹200.00.₹150.00Current price is: ₹150.00.Read moreNodeMCU is a IoT Module based on ESP8266 wifi Module. NodeMCU uses Lua Scripting language and is an open source Internet of Things (IoT) platform. This modules has CH340g USB to TTL IC.
Features of Node-MCU IoT Module:
- Open source IoT Platform
- Easily Programmable
- Low cost & Simple to Implement
- WI-FI enabled
Specification of Node-MCU IoT Module:
- It is based on ESP8266, integrates GPIO, PWM, IIC, 1-Wire and ADC all in one board.
- Power your development in the fastest way combining with NodeMCU Firmware!
- USB-TTL included, plug&play
- 10 GPIO, every GPIO can be PWM, I2C, 1-wire
