Digital Sensor TTP223B Module Capacitive Touch Switch
Original price was: ₹78.00.₹20.00Current price is: ₹20.00.
- Power supply voltage(VCC): 2.0, 3, 5.5 V.
- Output high VOH: 0.8 Vcc
- Output low VOL: 0.3 Vcc
- Response time (touch mode) : 60 mS
- Response time (low power mode) : 220 mS
- Can replace the traditional touch of a button
- Four M2 screws positioning holes for easy installation
In stock
TTP223B Capacitive Touch Key Sensor Module is based on a touch-sensing IC capacitive touch switch module. It allows you to remove the worry of conventional push-type keys.
Digital Capacitive Touch Switch Module is based on TTP223B. Normally, it outputs low and keeps at a low power state. When a touch is sensed on the circular marked region, it outputs high and switches to the quick response state. When not being touched for 12 seconds, it switches to a low power state again.
In addition to the thin paper ( non-metallic ) covering the surface of the module, as long as the correct location of the touch, you can make it hidden in the walls, desktops, and other parts of buttons.
Touch Sensor Interface :
- Touch area: Similar to a fingerprint icon inside the area, you can touch the trigger finger.
- Control Interface: A total of three pins (GND, VCC, SIG), GND to the ground, VCC is the power supply, SIG digital signal output pin
- Positioning holes: 4 M2 screws positioning hole diameter is 2.2mm, the positioning of the module is easy to install, to achieve the inter-module combination.
- Power Indicator: Green LED, power on the right that is shiny
Package Includes :
1 x TTP223B Capacitive Touch Key Sensor Module
| Weight | 85 g |
|---|
Related products
-
NODEMCU – ESP8266 Wifi Development Board
Original price was: ₹200.00.₹150.00Current price is: ₹150.00.Read moreNodeMCU is a IoT Module based on ESP8266 wifi Module. NodeMCU uses Lua Scripting language and is an open source Internet of Things (IoT) platform. This modules has CH340g USB to TTL IC.
Features of Node-MCU IoT Module:
- Open source IoT Platform
- Easily Programmable
- Low cost & Simple to Implement
- WI-FI enabled
Specification of Node-MCU IoT Module:
- It is based on ESP8266, integrates GPIO, PWM, IIC, 1-Wire and ADC all in one board.
- Power your development in the fastest way combining with NodeMCU Firmware!
- USB-TTL included, plug&play
- 10 GPIO, every GPIO can be PWM, I2C, 1-wire
-
Digital LDR Module – Light Sensor
Original price was: ₹50.00.₹35.00Current price is: ₹35.00.Read moreFeatures:
✅ Simple to use, plug-and-play.
✅ Adjustable sensitivity using potentiometer.
✅ Low power consumption.
✅ Fast switching compared to analog readings.
✅ Useful in light detection, automatic street lights, daylight sensing, and DIY projects.Applications:
🔹 Automatic night lamp.
🔹 Smart curtains that close when light is high.
🔹 Light intensity alarms.
🔹 Robotics line-following sensors (combined with reflective surfaces).
🔹 Security systems to detect sudden darkness (hand covering sensor). -
BLDC 30A ESC – Brushless DC Motor Electronic Speed Controller
Original price was: ₹550.00.₹350.00Current price is: ₹350.00.Add to cartBLDC 30A ESC – Key Specifications
-
Maximum Current: 30A for stable and BLDC Motor Controller
-
Peak Current: 40A (<10 sec) for high-performance bursts
-
BEC Output: 5V/2A to power receivers and electronics efficiently
-
Auto Cut-Off: 2.9V/cell for battery safety and protection
-
Compact Dimensions: 45 × 24 × 9 mm, lightweight 23 g design
-
Optimized for: Drones, RC cars, boats, and robotics applications
-
-
W1209 Digital Temperature Controller Thermostat Module
Original price was: ₹120.00.₹80.00Current price is: ₹80.00.Add to cartW1209 Temperature Controller Module – Specifications
-
Type: Digital temperature controller / digital temp controller
-
Input Power: 12V DC
-
Measuring Input: NTC 10K 0.5% sensor
-
Waterproof Sensor: 0.5M probe
-
Output: 1-channel relay, 10A capacity
-
Temperature Range: -50°C to +110°C
-
Resolution: 0.1°C (-9.9 to 99.9°C), 1°C for other ranges
-
Measurement Accuracy: ±0.1°C
-
Control Accuracy: ±0.1°C
-
Refresh Rate: 0.5 seconds
-
