BMP180 Digital Barometric Pressure Sensor Module
Original price was: ₹180.00.₹36.00Current price is: ₹36.00.
Features
- Measures barometric pressure, altitude & temperature
- High precision: ±1 hPa (pressure), ±0.5°C (temperature)
- Pressure range: 300–1100 hPa
- Operating voltage: 1.8V–3.6V (3.3V typical)
- I²C interface for easy integration
- Low power consumption (<1 μA in standby)
- Compact & lightweight (~2 g)
- Compatible with Arduino, Raspberry Pi & other microcontrollers
In stock
BMP180 Digital Barometric Pressure Sensor Module is used for measuring barometric pressure and altitude. It also has a temperature sensor for temperature compensation of pressure measurements. It uses push sensors for the BMP180. It offers a pressure measuring range of 300 to 1100 hPa with a relative pressure error of 0.12 hPa.
BMP 180 is a barometric pressure sensor with an I2C interface. Barometric pressure sensors measure the absolute pressure of the air around them. This pressure varies with both the weather and altitude. Depending on how you interpret the data, you can monitor changes in the weather, measure altitude, or any other tasks that require an accurate pressure reading.
Note: (1 hPa ≡ 100 Pa) which is equal to 0.001 bar (atmospheric)
Features :
- I2C interface.
- Max I2C Speed: 3.4Mhz
- Pressure conversion time: 5msec
- Fully calibrated.
- Small and easy to use.
- Voltage supply: 1.8 ~ 3.6 V
- Current supply: 5µA at 1Hz
- Peak current: 1000µA
- Very low noise: up to 0.02hPa (17cm)
- Pressure Range: 300hPa to 1100hPa (+9000m to -500m)
Package Includes :
- 1 x BMP180 Digital Barometric Pressure Sensor Module
- 1 x 4Burg Connector(Straight)
| Input Voltage | 1.8 ~ 3.6 V |
| Interface Type | I2C |
| Max I2C Speed | 3.4Mhz |
| PCB Size ( L x W ) | 1.3 x 1.2 cm |
| Peak Current | 1000µA |
| Pressure conversion time | 5 ms |
| Pressure Range | 300hPa to 1100hPa |
| Weight | 5 g |
|---|
Related products
-
Arduino Nicla Vision – ABX00051
Original price was: ₹8,980.00.₹7,999.00Current price is: ₹7,999.00.Add to cartFeatures
- Processor: STM32H747AII6 Dual Arm® Cortex® M7/M4 IC
- Camera: 2MP with integrated image processor
- AI-ready: Supports TensorFlow Lite for on-device inference
- Connectivity: Bluetooth® Low Energy, Wi-Fi (via external module)
- Memory: 1MB SRAM, 2MB Flash, 16MB external SPI Flash
- Sensors: IMU, microphone, distance sensor
- Low-power operation: ideal for battery-powered edge AI applications
- Compact size: 22.86 x 22.86 mm
- USB Type-C for programming and power
-
Arduino Nano Original A000005
Original price was: ₹2,500.00.₹1,470.00Current price is: ₹1,470.00.Add to cartTech specs
Microcontroller ATmega328 Architecture AVR Operating Voltage 5 V Flash Memory 32 KB of which 2 KB used by bootloader SRAM 2 KB Clock Speed 16 MHz Analog IN Pins 8 EEPROM 1 KB DC Current per I/O Pins 20 mA (I/O Pins) Input Voltage 7-12V Digital I/O Pins 22 (6 of which are PWM) PWM Output 6 Power Consumption 19 mA PCB Size 18 x 45 mm Weight 7 g Product Code A000005 -
4 Channel 5V Relay Module with Optocoupler
Original price was: ₹250.00.₹118.00Current price is: ₹118.00.Add to cartFeatures:
- Channel: 4 channel
- Relay Operating Voltage: 3.3V to 5V
- High impedance controller pin
- DC or AC signal, control, you can control the 220V AC load.
- There is a normally open and one normally close contact.
- Triode drive, increasing relay coil
- Pull-down circuit for avoidance of malfunction
- Power supply indicator and Control indicator lamp
- Power supply and relay instructions, lit, disconnect is off.
- Input signal, signal, common Terminal and start conducting.
- Useful for appliance control.
- One normally closed contact and one normally open contact
- The module is compliant with international safety standards, control and load areas isolation trenches.
* Product Image is shown for illustrative purposes only and may differ from actual product.
-
Mini Solderless Breadboard – 170 Tie Points
Original price was: ₹25.00.₹14.00Current price is: ₹14.00.Add to cartFeatures
- 170 Tie Points – Suitable for small-scale circuits and quick experiments.
- Solderless & Reusable – Components can be inserted and removed easily.
- Durable Build – ABS plastic body with nickel-plated contacts ensures long life.
- Self-Adhesive Backing – Stick to any flat surface or inside project enclosures.
- Interlocking Design – Can be connected to other breadboards for expansion.
- Supports 20–29 AWG solid core jumper wires and standard components.
